Lamp Module SpecificationsAppliance Module SpecificationsInstallationJoining To a TouchscreenResetting to Factory Default Settings
3 Series Lamp Module
The 3-Series Lamp Module introduces new functionality to existing in-home lighting systems. By placing the Lamp Module between an outlet and any lamp in your home, you can instantly add advanced automation features. The Lamp Module can also set dimming levels for any dimmable light bulb. Not only can the Lamp Module be dimmed remotely, but it also can be used with your existing ZigBee hub to respond to alerts, schedules, and scenes. The Lamp Module can also report its power usage for energy management. The 3-Series Lamp Module is an affordable way to add automation and track the energy use of your home.
SPECIFICATIONS
- Current sensing to report real time energy usage
- Override button for directly controlling output
- Over-the-air firmware updates
- Smaller compact design
- Built-in power amplifier for exceptional range
TECHNICAL SPECS
- Lamp Module(Model # ending with ZHAC)
Rated: 120 VAC, 60Hz - Output: 300W Incandescent
3 Series Appliance Module
The 3-Series Appliance Module introduces new functionality to existing appliances and lighting devices. By placing the Appliance Module between an outlet and any appliance in your home, you can instantly add advanced automation features. Not only can the Appliance Module be switched on and off remotely, but it also can be used with your existing ZigBee hub to respond to alerts, schedules, and scenes. The Appliance Module can also report its power usage for energy management. The 3-Series Appliance Module is an affordable way to add automation and track the energy use of your home.
SPECIFICATIONS
- Current sensing to report real time energy usage
- Override button for directly controlling output
- Over-the-air firmware updates
- Smaller compact design
- Built-in power amplifier for exceptional range
TECHNICAL SPECS
- Battery Type: Outlet
- Battery Life: N/A
- Dimension: 2.4″W x 2.6″H x 1.56″L
- Operating Temperature: 0° to 40°C
Installation
This step is applicable to all of the following models.
Centralite 3 Series Lamp Module
Centralite 3 Series Appliance Module
Centralite Azela Lamp Module (Legacy model – round top)
Centralite Azela Appliance Module(Legacy model – round top)
- Attach the plug from the lamp or appliance to be controlled into the receptacle of the Lamp/Appliance Module
- Note: Be sure that you are using an appliance module if you are controlling an appliance.
- Attach Lamp/Appliance Module to wall receptacle. Verify that the receptacle is powered. If the receptacle is powered by a wall switch, the wall switch must be kept ON at all times for the module to operate properly.
- Pair the Lamp/Appliance Module to your Touchscreen
Joining to the Touchscreen
- Navigate to Settings > Home Devices > Lighting > Add Lights
- The module will display a blue light that should flash 3 times each 5 seconds
- As the Touchscreen discovers lights, they will appear on the screen
- Once your device(s) is found, click next and follow the onscreen prompts to name and configure your device
If the touchscreen does not locate your lighting device, follow the steps below to reset your module to factory default settings and retry
Resetting
This step applies to the following models:
Centralite 3 Series Lamp Module
Centralite 3 Series Appliance Module
Centralite Azela Lamp Module (Legacy model – round top)
Centralite Azela Appliance Module(Legacy model – round top)
- Verify that the wall outlet is powered. If the wall outlet is powered by a wall switch, then the wall switch MUST be kept ON at ALL times for the Lamp Module to function.
- Attach the plug from the lamp or appliance to be controlled into the outlet of the Lamp Module.
- Press and hold the Lamp Module button.
- NOTE: The button for the AZELA models is on the side of the module.
- While still holding down the Lamp Module button plug the unit back into the wall outlet. After 2 Seconds the blue light on the module will turn on.
- Once the blue light is on let go of the button. The blue light will flash a few times every 5 seconds to signal that it is in pairing mode.